Skip to content
Topic: Rapid PVST+Switch

2.0 Switching and Network Access

Rapid PVST+ Practice Questions

Updated for CCNA v2.0

Root bridge selection, RSTP port roles and states, PortFast, root guard, loop guard, and BPDU guard.

CCNA v2.0 objectives 2.5, 2.5.a, 2.5.b, 2.5.c, 2.5.d · objective map

Author-reviewed by LabFabric · 25 September 2026 · Report a content issue

All 13 Rapid PVST+ questions in this set

Answers and explanations appear when you work through the set above.

  1. Which set lists the port states used by Rapid PVST+?

    • Discarding, learning, forwarding
    • Blocking, listening, learning, forwarding
    • Listening, learning, forwarding, disabled
    • Down, init, exstart, full
  2. Which RSTP port role provides a backup path to the root bridge through a different switch, and moves quickly to forwarding if the root port fails?

    • Alternate port (backup root path)
    • Backup port (same-segment redundancy)
    • Designated port (segment forwarder)
    • Disabled port (excluded from STP)
  3. Which command makes a switch the root bridge for VLAN 10 by lowering its bridge priority automatically?

    • spanning-tree vlan 10 root primary
    • spanning-tree vlan 10 priority 61440
    • spanning-tree vlan 10 root secondary
    • spanning-tree vlan 10 cost 1
  4. What is the default bridge priority on a Cisco switch before the VLAN ID is added?

    • 32768
    • 4096 (one priority increment)
    • 24576
    • 61440
  5. Which switch becomes the root bridge?

    • The switch advertising the lowest bridge ID
    • The switch advertising the highest MAC address
    • The one with the most ports
    • The one that boots first
  6. What does PortFast do on an access port connected to a PC?

    • Immediate forwarding, skipping normal STP convergence delay
    • Disables spanning tree on the switch so no ports process BPDUs
    • It raises the port speed to 1 Gb/s
    • It makes the port a trunk
  7. What does root guard do when it is enabled on a port?

    • Superior BPDUs put the port in root-inconsistent, blocking that root path
    • Any BPDU permanently shuts the port until an administrator reenables it manually
    • It blocks the port if BPDUs stop arriving
    • It makes the local switch the root for all VLANs
  8. What does loop guard protect against?

    • Missing BPDUs causing non-designated ports to forward
    • Prevents rogue DHCP servers from assigning an incorrect default gateway to hosts
    • Excess broadcasts sent by a single host on an access port
    • Spoofed source MAC addresses appearing on user-facing ports
  9. What does BPDU guard do to a PortFast-enabled port that receives a BPDU?

    • It places the receiving port in err-disabled
    • It ignores the BPDU
    • It raises the port to root port
    • It forwards the BPDU throughout the VLAN
  10. Two paths reach the root bridge with the same total root path cost. Which value does a switch compare next when choosing its root port?

    • The lowest sender bridge ID in the received BPDU
    • The highest port priority
    • The highest local MAC address
    • The lowest local port number, before sender ID
  11. Which show command displays the root bridge, bridge ID, and each port's role and state for VLAN 10?

    • show spanning-tree vlan 10
    • show vlan id 10
    • show interfaces trunk
    • show mac address-table vlan 10
  12. A user connected a small STP-capable switch to an access port, and BPDU guard err-disabled the port. To restore service, an AI assistant recommends no spanning-tree bpduguard enable on that port. What is the best evaluation?

    • Accept it, because BPDU guard should only be enabled on trunk ports
    • Reject: remove the rogue switch, then recover the port
    • Accept it, but also disable PortFast so that the port can safely receive BPDUs
    • Reject it, and enable root guard on the port instead so the switch is tolerated
  13. An AI assistant states that SW2 will become the root bridge for VLAN 10 because it has the lowest MAC address. show spanning-tree vlan 10 reports SW1's bridge priority as 24586 and SW2's as 32778. Which evaluation is correct?

    • The claim is correct, because the lowest MAC address always wins the root election
    • The claim is correct, because 32778 includes a larger extended system ID than 24586
    • The claim is wrong: SW1's lower priority wins before MAC comparison
    • The claim is wrong, because the switch with the most designated ports becomes root