Skip to content
Back to Learning
CCNP · ENCORAdvanced

OSPF Summarization and Network Types: Two Silent Faults

Area 3's summary is configured, yet the backbone still sees every host route and an ABR detours to reach its own area. Fix both on four real routers, right below.

Live lab: real routersOSPFSummarizationNetwork types

Symptom

The area 3 summary is configured, yet the backbone still sees every host route, and an ABR detours to reach its own area. Find both faults on four real routers.

Your mission

Prove the cause, then fix it

Format

Four real routers

Need a hint?

Reveal the root cause when you're ready.

Try the investigation first, then use this as your escape hatch, not a dead end.

Locked

Create a free account to open OSPF Summarization and Network Types: Two Silent Faults. You get the root cause and the full step-by-step fix.

Prefer no password? Use an email link instead

No spam. The fix lands in your inbox too. Your account includes 5 guided labs free. After that, the Learning Pass unlocks every remaining lab.

Lab debrief

Turn the session into a repeatable troubleshooting pattern.

Use this reference after your attempt: first explain the symptom, then verify the evidence, then confirm the repair.

The problem

Area 3 holds four server loopbacks, 172.16.99.1 to 172.16.99.4, behind two area border routers, R2 and R3. The design says the backbone should see them as one route, 172.16.99.0/24. Someone configured an area 3 range, but R1 still installs every host route. Meanwhile R3, which has its own link into area 3, sends its traffic for the servers through R1 and R2 instead.

What you'll practice

  • Read inter-area routes and summary LSAs to see what each area border router advertises
  • Explain why an area range only works on an ABR attached to the area being summarized
  • Summarize area 3 on both ABRs and prove the more specific routes are gone
  • Diagnose an OSPF network type mismatch that still lets the adjacency reach FULL
  • Prove the summary survives when one ABR loses its link into area 3

1. Where an area range works

An area range summarizes routes as they leave an area, so it only takes effect on an area border router with an interface in that area. On any other router IOS accepts the command and ignores it.

2. Why both ABRs need the range

Each ABR builds its own summary LSAs. If only one summarizes, the other still advertises every host route, and those more specific routes win over the summary.

3. The discard route

An ABR that summarizes installs the summary pointing to Null0. Addresses with a more specific route are forwarded as usual; an address in the range with no more specific route is dropped instead of looping.

4. Network type mismatch

If one end of a link runs point-to-point and the other broadcast, the hello and dead timers can still match and the adjacency still reaches FULL. The point-to-point side describes a direct router link while the broadcast side describes a transit network, so OSPF finds no usable path across the link and routes through it are missing.

5. Redundancy is part of the fix

The lab shuts R2's link to R4 to prove R3 can still advertise the /24 on its own. With the network type mismatch still in place, R1 would lose the server routes entirely at that point.

The topology

Four real routers. R1 sits in area 0, with a loopback in area 1. R2 and R3 are area border routers between area 0 and area 3, each with a link to R1 and a link to R4. R4 sits in area 3 and holds the server loopbacks 172.16.99.1 to 172.16.99.4.

Commands to run yourself

The real diagnostic commands for this lab, copy-paste ready. Run these in the same order to reproduce the investigation on your own session.

Every route R1 learns for the servers
show ip route ospf
Summary LSAs by area and advertising router
show ip ospf database summary 172.16.99.0
The network type on each end of a link
show ip ospf interface Ethernet0/1
The path traffic really takes
traceroute 172.16.99.1 source Loopback0
OSPF area 3 summarizationTwo ABRs connect the backbone to four server loopbacks in area 3.OSPF AREA 0OSPF AREA 310.0.12.0/30Et0/0 to Et0/010.0.13.0/30Et0/1 to Et0/010.0.24.0/30Et0/1 to Et0/010.0.34.0/30Et0/1 to Et0/1R1 · area 0 coreLo0 1.1.1.1Lo1 11.11.11.11 · area 1Et0/0 10.0.12.1Et0/1 10.0.13.1R2 · ABR 0/3Lo0 2.2.2.2Et0/0 10.0.12.2Et0/1 10.0.24.1R3 · ABR 0/3Lo0 3.3.3.3Et0/0 10.0.13.2Et0/1 10.0.34.1R4 · area 3Et0/0 10.0.24.2Et0/1 10.0.34.2Servers: Lo1 to Lo4172.16.99.1 to 172.16.99.4R1 sees four /32s, not one /24Four server routes reach the backboneR3 detours through R1 to reach area 3Its direct link to R4 is up

Rate this lab

No ratings yet

Your rating

Frequently asked

Are these real routers or a simulation?

Real routers. Pressing Start boots four routers just for you, with full command sets: any valid command works, not only the ones the guide suggests. The first start can take a minute or two while the lab server wakes up.

Who can run this lab?

It is included with the Exam Pass and the Year Pass. Each session lasts up to three hours, and you can run one live lab at a time.

Does my exact fix have to match the answer?

No. The lab checks the routers' state: the server routes R1 installs and which ABRs advertise the summary, R3's route over its direct link to R4, and R2's link. It never compares the commands you typed with an answer, so any fix that produces that state passes, and the tempting partial fixes do not.

Which ENCOR topics does it cover?

OSPFv2 multi-area operation, inter-area summarization and network types, from the Layer 3 section (3.2) of the 350-401 blueprint.

Ready to run this lab yourself?

No setup, no image sourcing. Book a session or ask for a live demo.